How to Remove Forend on Remington 870

Assuming you would like tips on how to remove the forend from a Remington 870 shotgun: The first step is to make sure the gun is unloaded. Next, locate the release button just behind the trigger guard and above the front sling swivel.

Pressing this releases the magazine cap, which is located at the end of the magazine tube (it may be necessary to wiggle it a bit). With the cap removed, slide the forend assembly forward off of the magazine tube. The entire process should only take a minute or two.

Magpul MOE Remington 870 Forend Removal and Installation

• First, make sure the gun is unloaded and remove any ammunition from the area
• Next, locate the two screws that hold the forend in place near the front of the gun
• Unscrew these two screws and set them aside
• The forend should now be loose and can be removed from the gun by simply sliding it off of the barrel

How to Remove Pins from Remington 870

If you have a Remington 870 shotgun, you may be wondering how to remove the pins that hold the gun together. Here is a step-by-step guide on how to do this: 1. First, make sure that the gun is unloaded and that there is no ammunition in the chamber.

2. Next, locate the two pins that hold the gun together at the front of the receiver. These are typically located just above the trigger guard. 3. Using a punch or other small tool, push out one of these pins from left to right.

The pin should come out easily once it’s started moving. Repeat this process for the second pin. 4. With both pins removed, you should now be able to separate the upper and lower receivers of the shotgun.

Be careful not to lose any small parts during this process!

Shotgun Forend Removal

If you need to remove the shotgun forend from your gun, there are a few steps you need to follow. First, make sure the gun is unloaded and pointed in a safe direction. Then, locate the release button on the forend (it is usually located near the front of the trigger guard).

Press and hold this button while pushing the forend forward and off of the gun. Once the forend is off, you can access the internal components of your shotgun. Be sure to reassemble your gun properly before firing it again.

Remington 870 Castle Nut Removal

If you need to remove the castle nut on your Remington 870, there are a few things you need to know. First, make sure the gun is unloaded and that the safety is on. Next, locate the two notches in the castle nut.

Using a 3/16″ drill bit, drill out the two pins that hold the castle nut in place. Once the pins are removed, the castle nut can be unscrewed by hand. Be careful not to lose any of the small parts that may fall out when removing the castle nut.

Once thecastle nut is removed, you will have access to the bolt assembly and trigger group.

Remington 870 Forend Removal Tool

If you own a Remington 870, then at some point you’re going to need to remove the forend. And while there are a few ways to do this, the best way is to use a forend removal tool. This tool makes it easy to remove the forend without damaging the gun, and it’s also much faster than other methods.

Simply insert the tool into the slot on the underside of the forend, and then twist it clockwise until the forend pops off. It’s really that simple! So if you need to remove your Remington 870’s forend, be sure to pick up a Removal Tool first.

Remington 870 Forend Assembly

The forend assembly is the part of the shotgun that houses the magazine tube, pump action, and action bars. The main purpose of the forend assembly is to provide a secure grip for the shooter’s hand while operating the shotgun. The forend assembly also provides a forward mounting point for accessories such as flashlights or lasers.

The Remington 870 is a pump-action shotgun that was first introduced in 1950. It is one of the most popular shotguns in the world, with over 10 million units sold. The 870 has been used by military, police, and civilians for everything from self-defense to hunting to competition shooting.

The forend assembly on a Remington 870 can be removed without tools by simply depressing two tabs on either side of the receiver and sliding it off (see image below). This allows easy access to the internals of the shotgun for cleaning or maintenance. Additionally, many aftermarket companies offer replacement or upgrade forend assemblies for those who want to change the look or feel of their shotgun.

Remington 870 Tips And Tricks

If you’re like most people, you probably think of the Remington 870 as just a simple pump-action shotgun. But this versatile weapon can do so much more than just shoot birds and deer. With the right accessories and a little bit of know-how, your 870 can become the ultimate home defense or tactical tool.

Here are just a few tips and tricks to get the most out of your Remington 870: 1. Add a pistol grip. This will give you much better control over the weapon, especially when firing from the hip.

It also makes it easier to perform speed reloads. 2. Install an extended magazine tube. This will increase your ammunition capacity, which is always handy in a defensive situation.

Just make sure you get one that’s specifically designed for the 870, as some aftermarket tubes can cause feeding problems. 3. Get a good flashlight mount. A flashlight is an essential piece of equipment for any self-respecting gun owner, and the 870 is no exception.

There are many different types of mounts available, so choose one that fits your needs and budget best. Personally, I prefer ones that attach to the receiver rather than the barrel since they tend to be more stable and durable. 4 .

Use slugs for home defense . While birdshot might be fine for taking down small game, it’s not going to do much against an intruder intent on doing you harm . Slugs , on the other hand , pack a serious punch and will stop just about anything in its tracks .

If you don’t feel comfortable using them indoors , consider keeping a slug gun like the Remington 1100 Tactical ready for action instead . Just remember : never fire blindly into a room without first identifying your target !

Credit: www.youtube.com

Q: How Do I Remove the Forend on My Remington 870

If you need to remove the forend on your Remington 870, first make sure that the gun is unloaded. Next, locate the two screws that secure the forend to the receiver – these will be located just behind the trigger guard. Using a Phillips head screwdriver, unscrew both of these screws until they are removed from the receiver.

At this point, you should be able to slide the forend off of the receiver. If it is stuck or seems tight, try wiggling it back and forth until it comes loose. Once it is off, you can put it aside and reassemble your gun when you’re ready.

Next, Locate the Pin That Secures the Forend to the Receiver

On most AR-15s, this is a takedown pin that goes through the receiver from left to right. On most AR-15s, there is a takedown pin that goes through the receiver from left to right which secures the forend to the receiver. This can be found towards the back of the gun near where the stock connects.

In order to remove this pin, you will need to push it out from the left side until it pops out on the right side. Be careful not to lose this pin as it is essential for reassembling your gun.

Using a Punch Or Other Tool, Drive Out the Pin from Left to Right

Assuming you are referring to a drive pin, also called a drift pin, used in construction and demolition: Using a punch or other tool, drive out the pin from left to right. The head of the drift pin is usually beveled, so that when it is driven into something, the head will countersink itself slightly.

When driving out the pin, use a sharp blow with the punch in order to avoid damage to the surrounding material.

The Forend Can Now Be Removed from the Receiver

Assuming you are talking about a shotgun: The forend is the part of the shotgun that you hold onto with your forward hand. It can now be removed from the receiver.

To do this, simply unscrew the nut that is located at the front of the trigger guard. This will allow you to take off the forend and access the inside of the gun.

Conclusion

If you need to remove the forend on your Remington 870, there are a few things you need to do. First, make sure that the gun is unloaded and the safety is on. Next, unscrew the action bars retaining nut, which is located under the forend.

Once this nut is removed, you can slide the forend off of the action bars. If you have any further questions about removing the forend on your Remington 870, please consult your owner’s manual.