How to Cut Gun Case Foam

To cut gun case foam, you will need a sharp knife and a cutting board. First, find the center of the foam block and make a mark. Then, using your knife, score the foam along the marked line.

Next, place the cutting board on top of the scored line and apply pressure to snap the foam in half. Finally, use your knife to trim any uneven edges.

  • Decide on the size and shape of the foam insert
  • Cut a piece of poster board or cardboard to use as a template
  • Trace the template onto the foam with a permanent marker
  • Cut along the line with a sharp utility knife or hot knife
  • Smooth any rough edges with sandpaper if necessary

Table of Contents

Best Tool for Cutting Gun Case Foam

If you’re looking for the best tool for cutting gun case foam, there are a few things to consider. First, you’ll want to make sure that the tool is sharp and can handle the material. Second, you’ll want to consider the size of the tool and how easy it is to maneuver.

Third, you’ll want to think about how much force is required to cut through the foam. With those factors in mind, we think the best tool for cutting gun case foam is a utility knife with a sharp blade. The size of the knife will depend on the thickness of the foam, but a standard utility knife should work well.

As for maneuverability, look for a knife with a slim profile so that it’s easy to control. And finally, keep in mind that some force will be required to cut through thicker pieces of foam – so don’t be afraid to put some muscle into it!

Where to Buy Foam for Gun Case

If you’re looking for foam to line your gun case, there are a few places you can check. Your local hardware store is a good place to start, as they may have some in stock. You can also check online retailers like Amazon or Foam Factory.

When choosing foam for your gun case, it’s important to consider the thickness and density of the foam. You want something that will provide enough padding to protect your guns, but not so thick that it makes the case too bulky or difficult to close. Once you’ve found the perfect foam for your gun case, cut it to fit using a sharp knife or electric carving tool.

Make sure all edges are smooth so they don’t catch on the inside of the case when you close it. Test the fit by putting all of your guns in the case and closing it up – if everything fits snugly and there’s no movement, you’re good to go!

Pelican Case Foam Cutting Tool

If you are in the market for a Pelican case, you may be wondering what is the best way to go about cutting the foam insert. There are a few different options available on the market, but we believe that the best tool for the job is the Pelican Case Foam Cutting Tool. This handy tool makes it easy to get a clean and precise cut every time, and it’s also very affordable.

The Pelican Case Foam Cutting Tool is a handheld device that uses a rotary blade to cut through foam. It has a comfortable grip and an adjustable depth guide so you can get the perfect cut every time. The blade is also replaceable, so you don’t have to worry about it getting dull over time.

We highly recommend this tool if you are looking for an easy and affordable way to customise your Pelican case. It’s also great for making repairs or modifications to existing cases. Order yours today and see how much difference it can make!

Custom Gun Case Foam

When it comes to protecting your guns, nothing beats a custom gun case foam insert. This type of foam is designed specifically for firearms, and offers superior protection against impact, vibration and moisture. Here are some things to keep in mind when choosing a custom gun case foam insert:

Choose the right size. Make sure the foam insert you choose is the right size for your gun case. Otherwise, it won’t offer adequate protection.

Pick a high-density foam. A high-density foam will better protect your guns from impact damage. Choose a foam with a density of at least 1.5 pounds per cubic foot (24 kilograms per cubic meter).

Look for closed-cell foam. Closed-cell foams are more resistant to moisture than open-cell foams, making them ideal for gun cases. They also resist mold and mildew growth.

Get an anti-static coating. Most firearm components are made of metal, which can create static electricity when rubbed against certain materials like polyurethane foam. An anti-static coating on your custom gun case foam will help prevent this from happening and protect your guns from potential damage caused by static discharge.

Cutting Pelican Foam With Hot Knife

Pelican foam is often used in packaging and as a protective material for fragile items. It can be cut with a hot knife, which heats the blade of the knife and melts the foam as it cuts. If you’re working with pelican foam, there are a few things you should keep in mind when cutting it with a hot knife.

First, make sure that your hot knife is properly heated – if it’s not hot enough, it won’t cut through the foam easily. Second, use a sharp blade – a dull blade will cause the foam to tear rather than cleanly slice through it. Finally, go slowly and carefully when making your cuts – rushing could result in an uneven or jagged edge.

With these tips in mind, cutting pelican foam with a hot knife is relatively easy and straightforward. Just take your time and be careful, and you’ll end up with clean, precise cuts every time.

How to Cut Gun Case Foam


How Do You Cut Soft Foam Inserts?

There are a few different ways that you can cut soft foam inserts, depending on the type of material and the desired outcome. For example, if you want to create clean, straight edges then you will need to use a sharp knife or rotary cutter. If you are looking to create more organic shapes then you can use scissors or even your hands to tear the foam.

No matter which method you choose, it is always best to start by sketching out your design on paper first. This will help you visualize the final product and make sure that all of your pieces fit together correctly. Once you have your design ready, lay the foam insert on a flat surface and begin cutting.

If using a knife, be sure to apply even pressure as you slice through the foam. You may need to go over some areas multiple times to get a clean cut. For curved edges, it is often easiest to start at the outside edge and work your way inwards.

Scissors can also be used to cut soft foam inserts, but they will not produce as clean of results as a knife would. If using scissors, make small snips into the foam rather than trying to cut through it in one continuous motion. This will help prevent the material from bunching up and creating uneven edges.

Once all of your pieces are cut out, it is time to assemble them! If necessary, use adhesive tape or glue sticksto secure the pieces together. And that’s it – now you have custom-fit soft foam inserts for whatever project you’re working on!

Do You Have to Cut the Foam in a Pelican Case?

No, you don’t have to cut the foam in a pelican case. The foam is designed to be cut to fit your specific equipment.

How Do You Cut Foam for a Tool Case?

When it comes to cutting foam for a tool case, there are a few things you need to keep in mind. First, you need to make sure that the foam is thick enough to protect your tools. Second, you need to make sure that the foam is cut correctly so that it fits snugly around your tools.

And third, you need to be careful not to damage the tools while cutting the foam. Here are a few tips on how to cut foam for a tool case: 1. Use a sharp knife: A sharp knife will make it easier to cut through the foam and will help you get a clean edge.

2. Cut slowly and carefully: Take your time when cutting the foam so that you don’t damage any of your tools. 3. Measure twice, cut once: Make sure you measure the area where you want to cut the foam before actually making any cuts. This will help ensure that the foam is cut correctly and fits snugly around your tools.

How Do You Cut 3 Inch Foam?

Assuming you would like tips on how to cut 3 inch foam: One way to cut 3 inch foam is by using an electric knife. First, make sure the blade of the knife is sharp and clean.

Second, mark the area you want to cut with a pen or pencil. Third, hold the foam steady with one hand while you carefully guide the electric knife through the marked area with your other hand. Fourth, apply even pressure as you move the knife back and forth until the foam is cut all the way through.

Another way to cut 3 inch foam is by using a hot wire cutter. First, make sure the wire is hot enough to melt through the foam (test it on a scrap piece of foam first). Second, mark the area you want to cut with a pen or pencil.

Third, hold the foam steady with one hand while you carefully guide the hot wire cutter through the marked area with your other hand. Fourth, apply even pressure as you move the cutter back and forth until the foam is melted all the way through.

Fastest way to cut foam for gun case!


If you’re looking for a quick and easy way to cut gun case foam, then you’ve come to the right place. In this article, we’ll show you how to cut gun case foam using a few simple tools. First, you’ll need a sharp knife or box cutter.

Next, find a straight edge to use as a guide for your cuts. Place the straight edge on top of the foam and align it with the edge of the foam that you want to cut. Then, simply run your knife along the straight edge, making sure to apply even pressure so that your cuts are clean and precise.

Once you’re finished cutting, remove any loose pieces of foam from your work area. And that’s all there is to it! With these simple steps, you can easily cut gun case foam like a pro.